What can I do with Vxdiag Vcx Nano GM?

It’s worth every penny to have a VXDIAG VCX NANO GM, you can use tech 2 to view and diag BCM, HVAC, issues, BOSE issues, etc…. HP Tuners is cool but having GM dealership diag and programming at home priceless.

USB Drivers, and software setup was a little bit of a PITA, its not exactly a straight forward install, and no instructions other than some youtube videos.

Problem and reason:

1st issue was the intermit issue

2nd issue was once the voltage dropped below the threshold the amp draw would disappear… 

in the end it was reproduceable after 3 on then off, then lock, key cycles. ended up being the MSM memory seat module (aka seat control module) well the dealer wanted time to program it for $90. Since I already replaced it, I was tired of paying the stealerships for 5 mins of coding. New MSM’s are blank and require programming, hence the need for this tool, nothing comes close as for cost and end result. 

Purchase:

http://www.chinacardiags.com/wholesale/xdiag-vcx-nano-for-gm-opel-gds2-diagnostic-tool-17409.html
https://www.acdelcotds.com/subscriptions

Solved:

Now on to the good news, new MSM installed and coded and working great and no amp draw, also playing around I found other control modules that needed to be updated

some things I saw available as well like – Afterblower option for our HVAC. Looks like we might be able to update to add a rear camera if we have the factory parts.

I even updated my Magnaride suspension F55, radio, HVAC, Drive door control module, some others had updates available. 

Images:

GM MDI GDS2 programming….

GM-MDI-GDS2-programming-1

GM-MDI-GDS2-programming-2

GM-MDI-GDS2-programming-3

GM-MDI-GDS2-programming-4

GM-MDI-GDS2-programming-5

GM-MDI-GDS2-programming-6

GM TECH 2 DIAG….

GM-TECH-2-DIAG-1

GM-TECH-2-DIAG-2

FAQs:

So did you have to buy the $250 software download and then $40 programming access for 1 vehicle or just the $40 programming access?

Software (tech 2) & MDI config is free with the tool on amazon for about $120, then if you want to program modules you get 1 VIN for 24 months/2 years unlimited for that 1 VIN for $40, so $160. I was able to get it to work on Windows 10 64bit. took some work to get all the Java updated, windows defender off, firewall off, update the scanners firmware, install passthru & GDS2, from VXDIG allscanner site’s website and go through all the GM stuff if you decide to update via the GDS2

If you just want a Tech 2 its comes with the VXDIAG, you access GDS2 programming its via GM’s acdelcotds site to install that software, there’s not a lot of documentation.

its an 01. the tech2 is needed to open the abs valves and it does a self bleeding procedure. I didn’t do any updates or stuff.

There is so much info to cover, computer info? windows 7, 10, 32 bit, 64bit?

the CD that came with my interface only had tech 2 & MDI software, and VMplayer to run GDS2 for 30 days, I am still trying to figure stuff out. 

Which version do you have wifi or usb? also try downloading the new VX manager from all scanners website (Chinese everywhere but you will see it towards the bottom), then update the VX interfaces drivers I believe as of writing this is 1.5xxx, (VX manager was buggy, I had to restart the application a few times and reboot once) from the VX manager of the left make sure to install pass-thru & GDS2/T2W drivers, I was not able to connect at all without all the drivers installed of this completed correctly. 

Getting the SPS working took a lot of Java updates and requiring me to turn off windows defender and firewall rules, also on GM’s site, you may purchase their version of the emulation software for tech 2 which is $275 (1x time fee) which I skipped on. I only pulled fault codes and looked at some tech 2 stuff but seemed ok, also did you have a battery charger on when you where bleeding? key on engine off eats power, as a former MB tech we always hooked up the battery charger anytime the SDS (MB’s tool) was connected. I will try playing around with the tech 2 some more I need to bleed the brakes on my 2016 Sierra.

I mostly used this for programming via SPS, best part is it will work for 2008-2017 GM vehicles for programing which for me and my entire family works perfect! 

GDS2 as it is global diag systems, only seems to work for most new vehciles like 2012 CTS since we are on a CTSV site, otherwise Tech 2 is the diag… tool used for most vehicles which would include abs bleed function.

So I’m having an issue with my drivers door not opening when i pull the handle (unlocked) and it’s not the micro switches (replaced). I’m thinking it’s a module issue or similar.

I presume I can troubleshoot it with this? I have an older laptop w/ Win 7 Pro SP1, 64 bit. Do you think this would work?

I have a similar issue on my daily driver 08 STS. I checked the continuity of the micro switches and they are good. I traced the wires down to where they go into the module and have continuity there as well. Here’s where I’m at from there. Can you hear the relays clicking inside the module with the door panel off? I think that’s a good indicator the module is working, I hear clicking in mine when pulling the handle. I didn’t have any clue on the pin out to check the wiring at the door actuator. But I can hear the actuator making sounds so it is definitely getting the signal to open. There’s something broke in the actuator/latch mechanism though. It’s all one piece. The actuator/latch/interior handle cable is one deal. I ordered one and it’s coming today. Don’t order the part from Tasca, they didn’t send mine for a week after ordering.

Hope this helps you finish troubleshooting but I would bet on the something dead within the latch/actuator assembly before the module.

http://blog.chinacardiags.com/

sales